70 KAMPF ALUMINIUM SLITTING LINE YEAR 2001

 

 70" Kampf Aluminum Slitting Line

Note:
According to Kampf, this Line will run Can Lid Stock 0.037" (0.93 mm) and
"O Temper" Dead Soft Aluminum at 0.081" (2.06 mm) with Knife Modifications.

Consisting of the Following:

Unwind Reels:
Coil O.D. Max.: 90" (2286 mm)
Coil O.D. Min.: 24" (610 mm)
Spool Size I.D./O.D./Length: 23.75" x 26" x 72" (603 x 660 x 1829 mm)
                             12.812" x 16" x 66" (325 x 406 x 1676 mm)
                             12" x 16" x 27.50" (304,8 x 406 x 698,5 mm)

Unwind and Coil Stands to be designed to accept future
Spool length of 76" (1930,4 mm)

Rewind Reels:
Slitting Width Range:      0.6" - 46" (15.8 mm - 1169 mm)
                           Maximum 40 Cuts Plus Edge Trim
Reels Diameter O.D. Max.:  72" (1829 mm)
               O.D. Min.:  18" (457 mm)
                           (Depending On Material Type, Thickness, Spool, Core
                           and Slitting Width)
Spool/Core I.D:            6, 10, 12, 16" (152, 254, 304, 406 mm)
                           Fiber Cores (Cardboard)
Slitting System:           Scissors Cut
Edge Trim Min./Max.:       0.5" - 2.0" Per Side (12.7 - 50.8 mm Per Side)
Slit Width Tolerance:      +/- 0.1 mm
Jogging Speed Approx.:     10 M/Min. (Adjustable)
Acceleration/Deceleration: Vo - V Max. in approx. 80 S
Instantaneous Stop:        V Max - Vo in approx. 40 S
Emergency Stop:            V Max - Vo in approx. 10 S
Winding Tension/Unwind:    Max. 12.650 N
Winding Tension/Rewind 1:  318 - 6328 N/25% Taper Tension at Outer Diameter
Winding Tension/Rewind 2:  318 - 8438 N/25% Taper Tension at Outer Diameter
Elongation Unit (Stretcher)
 Capability:               1.5 - 3.0% With a Target Of 2.0%

Machine Design: Drive side on the right, as seen in material running direction.

Power:
Voltage: 480 Volts + 10%-20% Ac-3 Phase-60 Cycle +/- 2%
Control Voltage: 24 Volts
Total Supply Value: approx. 700 Kva

Air:
Continuous Pressure: >/- 5,5 Bar >/- 77 Psi
Consumption approx.: 24 Nm3/H

Water:
Flow: 1,5 M3/H 53 Cu Ft/H

Main Machine:
 Drive Side on the right
 Unwind with Stepped Expanding Heads
 Stretch Stand
 Two Slitting Cassettes
 Pusher Plates on Rewinds
 Drives, Motors and Sps from Siemens
 Siemens Programming Unit with Modem and Programs

Winding Shafts:
 2 Rewind Shafts - 6"
 2 Rewind Shafts - 10"
 2 Rewind Shafts - 12"
 2 Rewind Shafts - 16"
 
Handling for Unwind Side including:
 Coil Car with Fixed Saddle
 Core Roller Table with Core Deposit
 Two Coil Deposit Stand Non-Driven (Spools 66", 72", 76")
 Empty Spool Roller Table with Spool Deposit

Handling for Rewind Side including:
 2 Finish Roll Transport Cars
 Edge Trim Suction, Chopper, Transport and Air-Separator, Diverter Gate,
  Vacuum Hose and Maintenance Platform.

Line was Re-Installed in 2016